Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Just about everyone maintains their own unique assumption about Tools You Need to Install a New Bathtub .
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the project can relocate rapidly; if you need to open up a wall surface to eliminate the old bathtub as well as place the new tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the new one. Ensure you have certified on your own for the task and fit attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you may need a professional plumber to make tube connections.
This post will assist you install a new tub in your washroom if you have already acquired a new bathtub and also do not need to change the setup of your previous supply of water pipes.
Your devices and also product checklist ought to comprise the following:
Preparing for the Setup
First of all, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, then the first thing you must do is detach the water. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted gain access to that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the same for the other faucet.
Switch on the water system as well as check all joints and brand-new pipework for leaks and tighten them if necessary. Fill up the bath tub and also examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been utilized a minimum of when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap as well as the sink. Safeguard the tap in place with the producer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the market. It is advisable to fit the floor tiles using waterproof or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on Installing A Bathtub. Thanks for taking the time to read through our article post. So long as you enjoyed reading our article plz be sure to pass it around. Thank-you for going through it.
Visit Our Site Report this page